Main Components
6 four-petal cream motifs; burgundy centers and outlines; straight join between motifs.
Recommended Materials
Use smooth cotton or cotton-blend yarn so the dimensional stitches remain crisp. A DK or light worsted weight works well for most of these runners. Choose a hook approximately 3.0–4.0 mm, adjusting until the fabric is firm but not stiff. You will also need a tapestry needle, scissors, stitch markers, rustproof blocking pins and a large blocking surface. For highly sculptural flowers, a slightly smaller hook helps the petals hold their shape.
Abbreviations – US Terms
MR = magic ring; ch = chain; sl st = slip stitch; sc = single crochet; hdc = half double crochet; dc = double crochet; tr = treble crochet; dtr = double treble crochet; BLO = back loop only; FLO = front loop only; sp = space; st/sts = stitch/stitches; rep = repeat; FO = fasten off.
Gauge & Sizing
Gauge is not critical for a decorative runner, but every repeated motif should match. Make one complete motif, block it, then measure it before making the rest. A typical finished width is 30–42 cm. Length can be adjusted by adding or removing repeats. Keep all motifs from the same yarn lot when possible.
Construction Plan
Make six identical four-petal motifs. Each motif is worked from a burgundy center outward into four cream fan petals, then outlined in burgundy. Join the motifs at their top and bottom points.
Motif Center
With burgundy, MR, ch 3 and 11 dc; join. Next round: create 8 rounded petals with [sl st, ch 3, 2 dc, ch 3, sl st] around the center.
Cream Petals
Join cream behind the burgundy center. Divide the round into four sections. In each section build a broad fan over several rows, increasing from 5 dc to 9–11 dc. Add two small ch-2 openings inside each petal to imitate the decorative holes.
Outline & Join
Work sc in burgundy around each cream petal, placing 2–3 sc at curves and ch-1 at narrow corners. Join adjacent motifs at the top/bottom burgundy points with sl st while completing the final round.
General Dimensional Flower Method
For a raised flower, begin with an MR and 10–12 sc. Build successive petal layers by making chain loops behind the previous round. A useful progression is: inner petals in ch-3 loops with [sc, hdc, 2 dc, hdc, sc]; middle petals in ch-5 loops with [sc, hdc, 4–5 dc, hdc, sc]; outer petals in ch-6 or ch-7 loops with [sc, hdc, dc, 4 tr, dc, hdc, sc]. Stagger each new petal between the petals below it. Shape the petals forward with your fingers after blocking.
Leaf Method
Ch 12–18 depending on the desired leaf length. Work sc, hdc, dc and tr progressively toward the center of the chain, then reverse the sequence toward the tip. Work 2–3 stitches in the final chain and crochet down the opposite side. For ribbed leaves, add surface slip stitches from base to tip and short diagonal veins. For fern fronds, crochet a long central chain and work small graduated leaflets along both sides.
Joining & Assembly
Block all flat base pieces before adding heavy appliqués. Lay the components directly over the reference photo arrangement: establish the center line first, then position the largest flowers or motifs, then leaves, buds and small decorations. Pin everything in place before sewing. Stitch through the firm lower layers of flowers so the upper petals remain free and dimensional. Use matching yarn and hide all joining stitches on the wrong side.
Finishing
Weave in every end securely. Wet-block cotton pieces and pin the lace openings, points and scallops individually so the runner dries symmetrical. After drying, reshape all flowers, butterflies, bows and leaves by hand. If the runner will be washed frequently, avoid glue and attach every decorative element with yarn stitches