Main Components
Repeating cream/burgundy medallions; large burgundy roses; blush roses; brown petals; sage leaves; burgundy scalloped border.
Recommended Materials
Use smooth cotton or cotton-blend yarn so the dimensional stitches remain crisp. A DK or light worsted weight works well for most of these runners. Choose a hook approximately 3.0–4.0 mm, adjusting until the fabric is firm but not stiff. You will also need a tapestry needle, scissors, stitch markers, rustproof blocking pins and a large blocking surface. For highly sculptural flowers, a slightly smaller hook helps the petals hold their shape.
Abbreviations – US Terms
MR = magic ring; ch = chain; sl st = slip stitch; sc = single crochet; hdc = half double crochet; dc = double crochet; tr = treble crochet; dtr = double treble crochet; BLO = back loop only; FLO = front loop only; sp = space; st/sts = stitch/stitches; rep = repeat; FO = fasten off.
Gauge & Sizing
Gauge is not critical for a decorative runner, but every repeated motif should match. Make one complete motif, block it, then measure it before making the rest. A typical finished width is 30–42 cm. Length can be adjusted by adding or removing repeats. Keep all motifs from the same yarn lot when possible.
Construction Plan
Crochet 5–6 large round cream lace medallions and join them end-to-end. Add burgundy scallops around each unit. Make one large burgundy rose for each major medallion, pairs of blush roses between them, plus brown accent petals and sage leaves.
Cream Medallion
Begin with MR and 16 dc. Build 5–7 openwork rounds using dc clusters, ch-3 spaces and larger ch-5 arches. Keep the medallion flat by increasing evenly. Finish the cream portion with broad arches that will receive the burgundy border.
Burgundy Border
Join burgundy in an outer arch. Work repeating shells such as [sc, hdc, 5 dc, hdc, sc], separated by sc anchors. Where two medallions meet, join corresponding shell points with sl st or ch bridges.
Rose Arrangement
Sew one large burgundy rose to the center of every second medallion. On the alternating spaces, place two smaller blush roses. Surround the large roses with 6–8 brown petal shapes and 4–6 sage leaves.
General Dimensional Flower Method
For a raised flower, begin with an MR and 10–12 sc. Build successive petal layers by making chain loops behind the previous round. A useful progression is: inner petals in ch-3 loops with [sc, hdc, 2 dc, hdc, sc]; middle petals in ch-5 loops with [sc, hdc, 4–5 dc, hdc, sc]; outer petals in ch-6 or ch-7 loops with [sc, hdc, dc, 4 tr, dc, hdc, sc]. Stagger each new petal between the petals below it. Shape the petals forward with your fingers after blocking.
Leaf Method
Ch 12–18 depending on the desired leaf length. Work sc, hdc, dc and tr progressively toward the center of the chain, then reverse the sequence toward the tip. Work 2–3 stitches in the final chain and crochet down the opposite side. For ribbed leaves, add surface slip stitches from base to tip and short diagonal veins. For fern fronds, crochet a long central chain and work small graduated leaflets along both sides.
Joining & Assembly
Block all flat base pieces before adding heavy appliqués. Lay the components directly over the reference photo arrangement: establish the center line first, then position the largest flowers or motifs, then leaves, buds and small decorations. Pin everything in place before sewing. Stitch through the firm lower layers of flowers so the upper petals remain free and dimensional. Use matching yarn and hide all joining stitches on the wrong side.
Finishing
Weave in every end securely. Wet-block cotton pieces and pin the lace openings, points and scallops individually so the runner dries symmetrical. After drying, reshape all flowers, butterflies, bows and leaves by hand. If the runner will be washed frequently, avoid glue and attach every decorative element with yarn stitches